繼續總結NR MRO中所使用的幾個流程的進一步信息，本篇文章也可以算作2021精華文（17）MRO相關規范總結的續集，用于進一步聊聊MRO中可能使用的幾條消息的詳細內容。首先在2021精華文（17）MRO相關規范總結講到RLF report的上報機制。UE使用在如下幾條RRC消息中的IE rlf-InfoAvailable-r16來告知網絡側它已經獲取到了相應的rlf信息，即為：

然后gNB收到UE的這個IE通知后，會通過如下這兩個消息要求UE上報已經獲取的rlf info，UE繼而將之報告gNB：

從上面這對RRC消息來看，gNB在UEInformationRequest-r16中包含了請求UE上報rlf的信息rlf-ReportReq-r16，然后UE在使用UEinformationResponse回應時將rlf report上報給gNB。RLF Report里的信息非常豐富，在MRO中的判決流程的主要信息依據，尤其重要，我們將之詳細展開，這里我們將重點關注NR rlf信息部分，重點的部分做了編號，如下所示：

1. 即 measResultLastServCell-r16

MeasResultRLFNR-r16,包含了NR服務小區的測量結果信息。這些信息包含了基于cell的測量結果和精細到cell內所使用的每個RS的測量結果，當然是可選的IE。

2和3. 第2和第3分別是針對NR鄰區和EUTRAN鄰區的測量結果，我們以NR鄰區為例，主要也是上報的NR鄰區及鄰區內各個RS的測量結果，那個CGIinfo-NR主要用于相關ANR流程：

measResultListNR-r16???????????????? MeasResultList2NR-r16

measResultListNR

This field refers to the last measurement results taken in the neighboring NR Cells, when the radio link failure or handover failure happened.

4.第四個是c-RNTI-r16，有關c-RNTI的規范文本如下，比較清晰：

This field indicates the C-RNTI used in the PCell upon detecting radio link failure or the C-RNTI used in the source PCell upon handover failure.

5.和6.用于指示之前切換中源cell所使用的兩類PCI，

This field is used to indicate the source PCell of the last handover (source PCell when the last RRCReconfiguration message including reconfigurationWithSync was received). For intra-NR handover nrPreviousCell is included and for the handover from EUTRA to NR eutraPreviousCell?is included.

7.和8.用于指示RLF發生所在的cell，包括了PCI（PCI+頻點）和eCGI：

This field is used to indicate the PCell in which RLF is detected or the target PCell of the failed handover. For intra-NR handover nrFailedPCellId is included and for the handover from NR to EUTRA eutraFailedPCellIdis included. The UE sets the ARFCN according to thefrequency band used for transmission/ reception when the failure occurred.

9.和10.指示的是在經歷了failure和重建失敗后最終實際連接的cell。使用CGI+TAC。

This field is used to indicate the cell in which the UE comes back to connected after connection failure and after failing to perform reestablishment. If the UE comes back to RRC CONNECTED in an NR cell then nrReconnectCellID is included and if the UE comes back to RRC CONNECTED in an LTE cell then eutraReconnectCellID is included.

11.?TimeUntilReconnection-r16::= INTEGER (0..172800)，記錄UE從RLF到重新進入連接態的時段。

This field is used to indicate the time that elapsed between the connection (radio link or handover) failure and the next time the UE comes to RRC CONNECTED in an NR or EUTRA cell, after failing to perform reestablishment.Value in seconds. The maximum value 172800 means 172800s or longer.

12.reestablishmentCellId，規范中定義如下，也是使用使用CGI+TAC：This field is used to indicate the cell in which the re-establishment attempt was made after connection failure.

13.timeConnFailure-r16，用于記錄從最近一次發起切換直到RLF發生的時段，規范中定義如下：

This field is used to indicate the time elapsed since the last HO initialization until connection failure. Actual value = field value * 100ms. The maximumvalue 1023 means 102.3s or longer.

14.timeSinceFailure-r16，用于記錄從RLF發生迄今為止所經歷的時間，規范文本如下：

This field is used to indicate the time that elapsed since the connection (radio link or handover failure）.Value in seconds. The maximum value 172800 means 172800s or longer.

15.connectionFailureType-r16，用于UE報告該failure是RLF還是切換失敗。就是connection failure類型。

16.rlf-Cause-r16，顧名思義即為RLF的原因值，即此字段用于指示上次檢測到的RLF的原因。在切換失敗的情況下（即connectionFailureType設置為“hof”），允許UE將該字段設置為任何值。

17. locationInfo-r16，用于指示報告各類location的，如下：

LocationInfo-r16::=????? SEQUENCE {

commonLocationInfo-r16??? CommonLocationInfo-r16????????? OPTIONAL,

bt-LocationInfo-r16?????? LogMeasResultListBT-r16???????? OPTIONAL,

wlan-LocationInfo-r16???? LogMeasResultListWLAN-r16?????? OPTIONAL,

sensor-LocationInfo-r16?? Sensor-LocationInfo-r16???????? OPTIONAL,

...

}

18. noSuitableCellFound-r16，UE在T311超時的時候使用它，表明搜不到合適的cell駐留。

在前文2021精華文（17）MRO相關規范總結已經說了RLF report報告的流程已經在Xn，NG，F(xiàn)1接口上的傳遞過程和消息。請參考之，此處不再贅述。